• lamp_A_USA
  • スクリーンショット 2017-07-21 15.39.50
  • D-007-bk1-rgb
  • D-007-bk2-rgb

007 Lamp AB Kit [USA]

007 Lamp AB Kit [USA]
Lamp Exclusive for Tension Rod A/B. The height of the lamp is also adjustable.

* Indoor Use only
* For Tension Rod A/B (Horizontal Use only) only
* We do not supply Electric Bulb and Switch. Please prepare the LED Bulb (26E: less than 10W) by yourself.

SPEC
Size: W280mm (11inch) H320mm (12.6inch) D97mm (3.8inch)
Weight: 700g (1.54lb)
Power Source / AC
Length of Code / 5m (16.4 feet)
Function: LED Lamp equipment
Material
Lamp Shade: Aluminum,
Pipe: Steel,
Screw: Brass, ABS, Steel Coating
Attachment: Manual Instruction

HOW TO USE

1. Please install this product to the tension rod before the tension rod itself is not installed between the contact surfaces. Loose the Brass Screw until the tip of the Brass Screw disappear from view inside the Sleeve Tubes (Sleeve A & Sleeve B) by checking the inside of the Sleeve Tubes by eye in order not to damage the pipes at the time of inserting this product into the tension rod.

2. Please remove the Large Round Cap on the outer pipe of the Tension Rod and insert Sleeve A and Sleeve B in this order with correct direction. Then, cover the removed cap.
* Please use the Large Round Cap of the tension rod.

 

 

3.Remove the EVA Pads on both ends of the tension rod.

4.Decide the position to install this product and fix the EVA Pads (removed from the end caps of the tension rod) on contact surfaces by Staplers or Screws.
* Please place the lamp more than 30cm away from the irradiated materials as well as contact surfaces.

 

Installation between Gypsum Plaster Boards

Please prepare the stapler which opens by more than 180 degree.(The stapler which is not open by more than 180 degree cannot be used.)
*In case the accompanying needles become short, please prepare the needles of size 10.
(Recommendable material is Stainless)

Open the stapler by 180 degree and staple the needles to the concave portion one by one while supporting the EVA Pads to the contact surfaces firmly. Please set the stapler horizontally to the contact surfaces to staple the needles vertically to the contact surfaces. Please staple the needles firmly.

 

Installation between Plywood Boards

Prepare #2 cross slot screw driver.

Fix the EVA Pads by the attached Screws while keeping the EVA pads to touch the contact surfaces
*In case of screwing up too much, the holes on the contact surfaces become big to the cause of idling. Please tight up the screws to the extent that the screws head does not float.

5. Install the Tension Rod by following the manual instruction. Set firmly the Large Round Caps into the fixed EVA Pads on the contact surfaces by rotating the Large Round Caps. Operating by 2 persons make it easier to install this product.

 

 

6.Make sure that the tension Rod is firmly installed. Then, fix this product on the tension rod by using the Brass Screws attached on the Sleeves of this product. Please do not let the Power Code loosen by fixing the Power Code on the Tension Rod by the attached Code Belt (L). The Power Code alongside of the wall should be fixed to the wall by the attached Belt Holder with Staplers or Screws and winded by Code Belt (S).
* Slack of the Power Code could cause the accident.

 

How to attach Belt Holder

Gypsum Plaster Board

Fix the 6 points of the concave portion by stapler.

Please staple the needles at a slant.

*Please use the needles attached to the Tension Rod. In case of running out of the needles, please prepare the needles of size 10. (Recommendable material is Stainless)

Installation between Plywood Boards

Fixed by Code Belt (S) and Belt Holder with screws.